Latest Products
-
MINI360 3A MINI DC-DC STEP DOWN CONVERTER VOLT REGULATOR 5V-23V TO 3. 6V 9V 12V
2.62€
-
5V Power Bank circuit board
4.17€
-
Micro Usb to Dip
2.96€
-
ICS43432 I2S Digital Microphone
10.12€
-
LED breakout module
4.17€
-
Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H
10.12€
-
GY-4466 Professional MAX4466 High Precision Electret Microphone Amplifier with Adjustable Gain for Arduino
7.14€
-
DC to DC HW613 step down
2.38€
-
Nand gate
1.19€
-
38KHz Infrared IR Receiver Sensor Module Geekcreit for Arduino ( Copy )
1.79€
-
Potentiometer 10k Ohms
0.36€
-
OP-AMP
1.19€
-
2N3904 transistor
1.19€
-
Raindrops Detection Sensor Module Compatible with Arduino
8.33€
-
PCB LoRa antenna
5.36€
-
Photoresistor Photo Light Sensitive Resistor Light Dependent Resistor
1.19€
-
helical coil antenna
5.36€
-
ARCELI DC to DC step down
2.98€
-
22402A-18 protoboard one side 5X7 cm
3.45€
-
22402A-18 protoboard two sided 5x7 cm
3.45€
-
22402A-18 protoboard two sided 4x6 cm
3.45€
-
22402A-17 protoboard two sided 2x8 cm
3.45€
-
22402A-17 protoboard two sided 3x7 cm
3.45€
-
WHITE LED's 5mm
0.36€
-
NeoPixel Stick - 8 x 5050 RGB LED with Integrated Drivers
5.95€
-
WHITE LED's 3mm
0.30€
-
mini push button switch 4 pin ( Copy )
0.60€
-
rocket switch 2 pin
0.60€
-
New Led Ring 16x 5050 RGB LED Board with Integrated Drivers Module Geekcreit for Arduino - products that work with official Arduino boards
7.14€
-
Slide switch 3 pin
0.60€
-
New LED Ring 24 x WS2812 5050 RGB LED with Integrated Drivers
9.52€
-
10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat Tube ( Copy )
4.17€
-
tactile switch 6 pin
0.60€
-
BLUE LED's 5mm
0.36€
-
Raspberry Pi Zero
21.42€
-
1N4007 Schottky Rectifier Diode
1.19€
16 ultra bright smart LED are arranged in a circle with 1.75" (44.5mm) outer diameter.
The rings are 'chainable' - connect the output pin of one to the input pin of another. Use only one microcontroller pin to control as many as you can chain together!
Each LED is addressable as the driver chip is inside the LED.
Each one has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and no external choke resistors are required making the design slim.
Power the whole thing with 5VDC (4-7V works) and you're ready to rock.
There is a single data line with a very timing-specific protocol.
Since the protocol is very sensitive to timing, it requires a real-time microconroller such as an AVR, , PIC, mbed, etc.
It cannot be used with a Linux-based microcomputer or interpreted microcontroller such as the netduino or Basic Stamp.
As it requires hand-tuned assembly it is only for AVR cores but others may have ported this chip driver code so please google around.
An 8MHz or faster processor is required.
Comes as a single ring with 16 individually addressable RGB LEDs assembled and tested.
- Availability: 4