Latest Products
-
MINI360 3A MINI DC-DC STEP DOWN CONVERTER VOLT REGULATOR 5V-23V TO 3. 6V 9V 12V
2.62€
-
5V Power Bank circuit board
4.17€
-
Micro Usb to Dip
2.96€
-
ICS43432 I2S Digital Microphone
10.12€
-
LED breakout module
4.17€
-
Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H
10.12€
-
GY-4466 Professional MAX4466 High Precision Electret Microphone Amplifier with Adjustable Gain for Arduino
7.14€
-
DC to DC HW613 step down
2.38€
-
Nand gate
1.19€
-
38KHz Infrared IR Receiver Sensor Module Geekcreit for Arduino ( Copy )
1.79€
-
Potentiometer 10k Ohms
0.36€
-
OP-AMP
1.19€
-
2N3904 transistor
1.19€
-
Raindrops Detection Sensor Module Compatible with Arduino
8.33€
-
PCB LoRa antenna
5.36€
-
Photoresistor Photo Light Sensitive Resistor Light Dependent Resistor
1.19€
-
helical coil antenna
5.36€
-
ARCELI DC to DC step down
2.98€
-
22402A-18 protoboard one side 5X7 cm
3.45€
-
22402A-18 protoboard two sided 5x7 cm
3.45€
-
22402A-18 protoboard two sided 4x6 cm
3.45€
-
22402A-17 protoboard two sided 2x8 cm
3.45€
-
22402A-17 protoboard two sided 3x7 cm
3.45€
-
WHITE LED's 5mm
0.36€
-
NeoPixel Stick - 8 x 5050 RGB LED with Integrated Drivers
5.95€
-
WHITE LED's 3mm
0.30€
-
mini push button switch 4 pin ( Copy )
0.60€
-
rocket switch 2 pin
0.60€
-
New Led Ring 16x 5050 RGB LED Board with Integrated Drivers Module Geekcreit for Arduino - products that work with official Arduino boards
7.14€
-
Slide switch 3 pin
0.60€
-
New LED Ring 24 x WS2812 5050 RGB LED with Integrated Drivers
9.52€
-
10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat Tube ( Copy )
4.17€
-
tactile switch 6 pin
0.60€
-
BLUE LED's 5mm
0.36€
-
Raspberry Pi Zero
21.42€
-
1N4007 Schottky Rectifier Diode
1.19€
MAX7219 is an integrated serial input / output common-cathode display drivers , which connects the microprocessor 7-segment digital LED display with 8 digits , bar graph can also be connected monitor or 64 separate LED. On type B BCD encoder includes an on-chip , multi-channel scanning loop , segment word drive, but also a 8x8 static RAM for storing each data . Only one external register is used to set the segment current for each LED .
A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update does not overwrite all of the display . MAX7219 also allows the user to select each of the data code or not coded .
The entire device includes a 150μA low-power shutdown mode , analog and digital brightness control , a scan-limit register allows the user to 1-8 bits of data , there is an LED light so that all the detection mode .
Requires only three IO ports can drive a dot ! No flashing dot matrix display ! Support cascade !
Single module can drive a common cathode 8 * 8 dot matrix
Module Operating voltage : 5V
Module size : 5 cm X 3.2 cm wide X 1.5 cm high
Holes with four screws , diameter 3mm, can be fixed by using our M3 studs
Mdules with input and output interfaces , support for cascading multiple modules
aeProduct.getSubject()
Is a block left input port, an output port on the right .
When control of a single module , simply input port receiving CPU
When cascading multiple modules 3 , output and input termination CPU, the input output termination module of the first two modules of the first one , the first two modules of terminating the input of the first three modules , and so on . ..
To 51 single example:
VCC → 5V
GND → GND
DIN → P22
CS → P21
CLK → P20
aeProduct.getSubject()
1PCS MAX7219 dot matrix module ( finished with lattice , has tested well )
5PCS DuPont line
- Availability: 2