Latest Products
-
2WD aluminium robot chassis - RED
19.90€
-
2WD aluminium robot chassis - BLUE
19.90€
-
MINI360 3A MINI DC-DC STEP DOWN CONVERTER VOLT REGULATOR 5V-23V TO 3. 6V 9V 12V
2.62€
-
5V Power Bank circuit board
4.17€
-
Micro Usb to Dip
2.96€
-
ICS43432 I2S Digital Microphone
10.12€
-
LED breakout module
4.17€
-
Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H
10.12€
-
GY-4466 Professional MAX4466 High Precision Electret Microphone Amplifier with Adjustable Gain for Arduino
7.14€
-
DC to DC HW613 step down
2.38€
-
Nand gate
1.19€
-
38KHz Infrared IR Receiver Sensor Module Geekcreit for Arduino ( Copy )
1.79€
-
Potentiometer 10k Ohms
0.36€
-
OP-AMP
1.19€
-
2N3904 transistor
1.19€
-
Raindrops Detection Sensor Module Compatible with Arduino
8.33€
-
PCB LoRa antenna
5.36€
-
Photoresistor Photo Light Sensitive Resistor Light Dependent Resistor
1.19€
-
helical coil antenna
5.36€
-
ARCELI DC to DC step down
2.98€
-
22402A-18 protoboard one side 5X7 cm
3.45€
-
22402A-18 protoboard two sided 5x7 cm
3.45€
-
22402A-18 protoboard two sided 4x6 cm
3.45€
-
22402A-17 protoboard two sided 2x8 cm
3.45€
-
22402A-17 protoboard two sided 3x7 cm
3.45€
-
WHITE LED's 5mm
0.36€
-
NeoPixel Stick - 8 x 5050 RGB LED with Integrated Drivers
5.95€
-
WHITE LED's 3mm
0.30€
-
mini push button switch 4 pin ( Copy )
0.60€
-
rocket switch 2 pin
0.60€
-
New Led Ring 16x 5050 RGB LED Board with Integrated Drivers Module Geekcreit for Arduino - products that work with official Arduino boards
7.14€
-
Slide switch 3 pin
0.60€
-
New LED Ring 24 x WS2812 5050 RGB LED with Integrated Drivers
9.52€
-
10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat Tube ( Copy )
4.17€
-
tactile switch 6 pin
0.60€
-
BLUE LED's 5mm
0.36€
VL53L0X Time-of-Flight (ToF) Laser Ranging Sensor Breakout 940nm GY-VL53L0XV2 Laser Distance Module I2C IIC 3.3V/5V
9.52€
The VL53L0X from ST Microelectronics is a time-of-flight ranging system integrated into a compact module. This board is a carrier for the VL53L0X, so we recommend careful reading of the VL53L0X datasheet (1MB pdf) before using this product.
The VL53L0 uses ST's FlightSense technology to precisely measure how long it takes for emitted pulses of infrared laser light to reach the nearest object and be reflected back to a detector, so it can be considered a tiny, self-contained lidar system. This time-of-flight (TOF) measurement enables it to accurately determine the absolute distance to a target without the object's reflectance greatly influencing the measurement. The sensor can report distances of up to 2 m (6.6 ft) with 1 mm resolution, but its effective range and accuracy (noise) depend heavily on ambient conditions and target characteristics like reflectance and size, as well as the sensor configuration. (The sensor's accuracy is specified to range from ±3% at best to over ±10% in less optimal conditions.)
Ranging measurements are available through the sensor's I⊃2;C (TWI) interface, which is also used to configure sensor settings, and the sensor provides two additional pins: a shutdown input and an interrupt output.
The VL53L0X is a great IC, but its small, leadless, LGA package makes it difficult for the typical student or hobbyist to use. It also operates at a recommended voltage of 2.8 V, which can make interfacing difficult for microcontrollers operating at 3.3 V or 5 V. Our breakout board addresses these issues, making it easier to get started using the sensor, while keeping the overall size as small as possible.
The VL53L0 uses ST's FlightSense technology to precisely measure how long it takes for emitted pulses of infrared laser light to reach the nearest object and be reflected back to a detector, so it can be considered a tiny, self-contained lidar system. This time-of-flight (TOF) measurement enables it to accurately determine the absolute distance to a target without the object's reflectance greatly influencing the measurement. The sensor can report distances of up to 2 m (6.6 ft) with 1 mm resolution, but its effective range and accuracy (noise) depend heavily on ambient conditions and target characteristics like reflectance and size, as well as the sensor configuration. (The sensor's accuracy is specified to range from ±3% at best to over ±10% in less optimal conditions.)
Ranging measurements are available through the sensor's I⊃2;C (TWI) interface, which is also used to configure sensor settings, and the sensor provides two additional pins: a shutdown input and an interrupt output.
The VL53L0X is a great IC, but its small, leadless, LGA package makes it difficult for the typical student or hobbyist to use. It also operates at a recommended voltage of 2.8 V, which can make interfacing difficult for microcontrollers operating at 3.3 V or 5 V. Our breakout board addresses these issues, making it easier to get started using the sensor, while keeping the overall size as small as possible.
- Availability: 1