Latest Products
-
2WD aluminium robot chassis - RED
19.90€
-
2WD aluminium robot chassis - BLUE
19.90€
-
MINI360 3A MINI DC-DC STEP DOWN CONVERTER VOLT REGULATOR 5V-23V TO 3. 6V 9V 12V
2.62€
-
5V Power Bank circuit board
4.17€
-
Micro Usb to Dip
2.96€
-
ICS43432 I2S Digital Microphone
10.12€
-
LED breakout module
4.17€
-
Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H
10.12€
-
GY-4466 Professional MAX4466 High Precision Electret Microphone Amplifier with Adjustable Gain for Arduino
7.14€
-
DC to DC HW613 step down
2.38€
-
Nand gate
1.19€
-
38KHz Infrared IR Receiver Sensor Module Geekcreit for Arduino ( Copy )
1.79€
-
Potentiometer 10k Ohms
0.36€
-
OP-AMP
1.19€
-
2N3904 transistor
1.19€
-
Raindrops Detection Sensor Module Compatible with Arduino
8.33€
-
PCB LoRa antenna
5.36€
-
Photoresistor Photo Light Sensitive Resistor Light Dependent Resistor
1.19€
-
helical coil antenna
5.36€
-
ARCELI DC to DC step down
2.98€
-
22402A-18 protoboard one side 5X7 cm
3.45€
-
22402A-18 protoboard two sided 5x7 cm
3.45€
-
22402A-18 protoboard two sided 4x6 cm
3.45€
-
22402A-17 protoboard two sided 2x8 cm
3.45€
-
22402A-17 protoboard two sided 3x7 cm
3.45€
-
WHITE LED's 5mm
0.36€
-
NeoPixel Stick - 8 x 5050 RGB LED with Integrated Drivers
5.95€
-
WHITE LED's 3mm
0.30€
-
mini push button switch 4 pin ( Copy )
0.60€
-
rocket switch 2 pin
0.60€
-
New Led Ring 16x 5050 RGB LED Board with Integrated Drivers Module Geekcreit for Arduino - products that work with official Arduino boards
7.14€
-
Slide switch 3 pin
0.60€
-
New LED Ring 24 x WS2812 5050 RGB LED with Integrated Drivers
9.52€
-
10 Grid Digital Segment LED Light Bar 10 Flat Tube of Super Bright 2 Red+3 Yellow+4 Green+1 Blue Light Flat Tube ( Copy )
4.17€
-
tactile switch 6 pin
0.60€
-
BLUE LED's 5mm
0.36€
Specifications:
Dimension: 12 x 12mm
Working Voltage: DC 2-5V
Timing can be set to a minimum to a maximum of 2 seconds 1,000 hours
Function and Design
1. The circuit according to claim connected and set a good time resistance and supply voltage;
2. Before the power not trigger output is high;
3. Trigger terminal "falling" trigger effective immediately
after the trigger output terminal goes low at the same time start the timer circuit;
4. Set the timer time to recover after the output terminal is high, wait for the next "falling" trigger;
5. The chip is not repeated triggered, meaning that
continue to trigger in the period after the trigger chip output low if the trigger is invalid;
6. The trigger end of "falling" Trigger refers to the instantaneous change from high level to a low level;
7. General refers to VCC high voltage, low means 0-0.3v or GND,
provided that they meet the level requirements can be;
8. trigger terminal can be connected to touch switch or microcontroller IO port or
other digital circuits have a "falling" can effectively trigger;
9. The trigger can be designed to power, only to trigger a short circuit to ground, power is triggered,
the time to recover after the output to a high level, waiting for the next
Falling edge trigger again.
Chip Features:
1. The use of low-power CMOS technology, lead-free and environmentally friendly.
2. Direct Push can output low LED
(please add current limiting resistor), the output high may push transistor (please add current limiting resistor).
3. Available resistance adjusting timing, there are 8 * N (N = 0.1.2.3) times the timing selection,time can be adjusted from 2s-1000h.
4. Optional trigger timing and triggering termination ground electric timer.
5. standby output high, falling edge trigger, post-trigger output low, after the delay recovery high.
Dimension: 12 x 12mm
Working Voltage: DC 2-5V
Timing can be set to a minimum to a maximum of 2 seconds 1,000 hours
Function and Design
1. The circuit according to claim connected and set a good time resistance and supply voltage;
2. Before the power not trigger output is high;
3. Trigger terminal "falling" trigger effective immediately
after the trigger output terminal goes low at the same time start the timer circuit;
4. Set the timer time to recover after the output terminal is high, wait for the next "falling" trigger;
5. The chip is not repeated triggered, meaning that
continue to trigger in the period after the trigger chip output low if the trigger is invalid;
6. The trigger end of "falling" Trigger refers to the instantaneous change from high level to a low level;
7. General refers to VCC high voltage, low means 0-0.3v or GND,
provided that they meet the level requirements can be;
8. trigger terminal can be connected to touch switch or microcontroller IO port or
other digital circuits have a "falling" can effectively trigger;
9. The trigger can be designed to power, only to trigger a short circuit to ground, power is triggered,
the time to recover after the output to a high level, waiting for the next
Falling edge trigger again.
Chip Features:
1. The use of low-power CMOS technology, lead-free and environmentally friendly.
2. Direct Push can output low LED
(please add current limiting resistor), the output high may push transistor (please add current limiting resistor).
3. Available resistance adjusting timing, there are 8 * N (N = 0.1.2.3) times the timing selection,time can be adjusted from 2s-1000h.
4. Optional trigger timing and triggering termination ground electric timer.
5. standby output high, falling edge trigger, post-trigger output low, after the delay recovery high.
- Availability: 10